Need professional heating and cooling services in Hopewell Junction, NY? Look no further! Folkes Home Services, Cooling & Burner Service provides expert services from highly trained technicians. We work for your comfort and satisfaction.
Check out our customer reviews below to see examples of our high quality work. Choose Folkes as your HVAC specialist in Hopewell Junction, NY.
Local Reviews
for Hopewell Junction, NY
Powered by Nearby NowOur Reviews by City
NA
🙂 - Hopewell Junction, NY
NA
Danny is the best~~
Denise - Hopewell Junction, NY
Annual AC maintenance
Pat - Hopewell Junction, NY
Tech’s maintenance was thorough and explained everything he did .
sytem check
Ramona - Hopewell Junction, NY
great service
Prompt Service, UNREASONABLE price!
George - Hopewell Junction, NY
To start, my technician Scott was wonderful. Very professional and knowledgeable. However, Folkes charged me $734 for replacing a capacitor, which after some research is only a $79 part (not a Chinese replica, but the SAME part that was installed. This was not an emergency call, nor was it unique or outdated equipment that was difficult to service. Very satisfied with the service, but will not use them again due to their surprisingly high price.
Fast Response Time
Sara - Hopewell Junction, NY
Called early Saturday with an issue. Customer service made sure a technician got to me home within a few hours.
Wonderful Customer Service
Sara - Hopewell Junction, NY
Shopped around for a replacement AC. Folkes had the best prices. Technicians arrived on time and kept me informed about their progress. They made sure that I understood what they did and how to best use my new unit. Would highly recommend.
Good Job!
Joanne - Hopewell Junction, NY
Great service
Luis - Hopewell Junction, NY
Noah is very professional.
Ac repair
Raymond - Hopewell Junction, NY
Useless this company should coordinate tech support time with the customers appointment not wait for 3 hrs doing nothing but waiting on hold and charging for it
Excellent
Fred - Hopewell Junction, NY
Very knowledgeable. Did a great job
Excellent
Fred - Hopewell Junction, NY
Had the problem figured out in 10 min
Done in a timely manor
Mark - Hopewell Junction, NY
Was not home but daughter was. Glad he could fix it because of the heat wave
Great service!
Ila - Hopewell Junction, NY
Tony was professional, efficient and courteous. He explained the entire service he was going to perform on my air conditioners, answered my questions and explored all options available to me, .
Waste of time
JM - Hopewell Junction, NY
Air conditioner condenser fan blade broke. Came out to do a service visit to check. Had I known the technician was simply going to just write down the model number of my unit I would have saved them the visit! Have to wait through the whole weekend without AC without any plan other than “we will find out the blade part number on Monday”. Instead, I took 5 minutes to find the part number on the blade. They noted “would probably be $500 to fix likely.” The blade is no more than $80, so I don’t know what that type of markup is. Again, no plan or care that I’ll be without AC until the part number is found… then ordered… then rescheduled to fix. Good thing I know how to use a screwdriver and took the 10 minutes to find the part number on the blade myself… I guess a $90 service visit saved me $500 since this is clearly something someone can do on their own. Don’t have something break on a Friday. It’ll only be a priority on Monday. And then maybe a part can get ordered for sometime the following week. Thank goodness for screwdrivers + internet + Amazon.
good job
sc - Hopewell Junction, NY
knowledgeable
great service...have been with them since 2002...wouldn't change!!!
Lucy - Hopewell Junction, NY
Thank you to Jackie, who took my call regarding air conditioning not working at 6pm...to having Tony P. come and service at7pm. Always a great team at Folkes
The service was great. The technician was kind, caring, well poised I will not only keep this company for all future plumbing, but also will request S
Parnel - Hopewell Junction, NY
Prompt and Effective
John Morgan - Hopewell Junction, NY
Scott got the AC back up and running. It’s just a mystery as to why the circuit breaker tripped.
Great Service
Anish - Hopewell Junction, NY
Horrible
Joe - Hopewell Junction, NY
The service guy was great and respectful only here for 5 minutes but your company is a rip off and will never call you again This service has nothing to do with the guy who came
Outstanding
Dr - Hopewell Junction, NY
Awesome Service!
Valerie - Hopewell Junction, NY
Friendly, knowledgeable technician! Awesome, convenient service
Honest, friendly, professional service
Eileen - Hopewell Junction, NY
I would recommend Folkes. Did a great job
charged a/c
Richard - Hopewell Junction, NY
Came quickly & Took care of the problem. It was hot & uncomfortable. Not anymore!
Margaret M.
I arrived to customer home to check a shower control that was leaking,I inspected the shower control and need to be replace the cartridge is very old and the two shut off valves in the side are broken because customer was using those valve to control the water demand, I provide an estimate to install a new shower control and install to 3/4†shut off valves for water heater,there is not valves except the one from the after the meter . Customer agree to estimate and we will reschedule for Thursday 08/05/2021 first call of the day. Customer pay half deposit. Deposit $960.41 of total of $1776.49
Margaret M.
Need to return when central Hudson installs gas meter. We will remove existing electric water heater at that time and tie the new tankless water heater into the hot and cold water lines. Bring 2-3†bird screens for furnace flue/fresh air terminations
Chris H.
Customer is getting loud vibration noise from first floor condenser, went to unit and unit has a bearing noise coming from condenser fan motor, tested amp draw on fan motor which is rated for .77 and my reading was .95, fan motor failing will need to give customer pricing and availability to replace fan motor.
Chris H.
Customers water heater leaking from bottom of tank due to heavy corrosion of rust it’s a 75 gallon power vented water heater that folkes installed in 2016 so warranty form will need to be filled out, took pictures and deposit to replace water heater also customer decided after I ran card he would like a drain pan for water heater as well added to bill
Margaret M.
Install Mitsubishi 3zone 3ton unit 100 ft of line set pressure test at 600 psig vacuum and program remote explained to customer how system works and he would like a copy of warranty by email or mail their is a balance of $6893.28 which is paid by check #2707
Tony P.
Completed annual ac tune up of two systems. Systems are not operating properly. Customer bought home two weeks ago. I found both air handlers and evap coils are original to home but both outdoor condensers have been replaced. Found used copper fittings all behind condenser laying on ground which indicates someone was here within the last couple of months to perform some sort of repairs. I believe previous homeowner tried to make it look like the house had operating systems. Second floor evap coil is rated for R22 ONLY and found it’s connected to a 410a ONLY condenser. Delta t is about 9 degrees for both floors. Recommend replacement of both systems. Found second floor coil plugged solid with dust and dirt. Completely cleaned from top to bottom of coil.
Noah D.
Performed ac tune up. Cleaned coils and tested the system. Cleared the condensate drain. No issues to report.
Chris H.
Completed full duct cleaning of two systems. Each grill was taken down and wiped/disinfected. Also completed Uv light installation on system in attic.
Greg M.
Found second floor condenser not energizing. System off on low pressure switch. R22 system has no refrigerant. Second floor system needs to be replaced. Set appointment for,replacement estimate.
Margaret M.
Folks arrived on 07/30/2021 to install a new well tank.Upon arrival I cut the power to the old well tank. I then drained the tank down and began to cut the old one out. I then removed the old tank and old valve. After that I put the new tank in and connected to the old poly line from the well and connect back to the house. I added a new shut off valve after the tank. I then checked the pressure of the tank and it was at the right pressure. I then wired the tank back up and turned the power on. I checked that the pressure switch was working correctly, the pump turned on at 40psi and shut off at 60psi. There are no leaks and the customer is satisfied. I thanked the customer for using folks and left.
Chris H.
Customer had no hot water in whole home, went to boiler primary not tripped, zone valve for hot water indirect tank calling, pulled cover off and end switch not making contact forced zone valve to make contact and boiler came on, customer has a bad zone valve recommended to change whole zone valve due to antifreeze and corrosion, customer declined repairs today her son in law is a plumber and will take care of repair. Forced end switch open so customer could have hot water.
Margaret M.
This is to install a new water treatment meant system including an ASP2 well sanitizing system to help with the hardness, as well as a uv light filter combo to help kill the bacteria that can form in the well. Folks arrived on 07/30/2021 to install water softener and uv light. Upon arrival I started by turning the water off to the house and draining the house down. I then cut into the water line and sent a line from the well and one from the house through the wall into the closet. I then began to pipe into the units I started by piping in the softener from the well, out of the softener into the filter, the filter then went to the uv light and then back to the house. I also put valves on both sides of the filter to have easier access changing the filter. I explained to the customer how to change the filter and set the counter for the uv light to 365. The softener was programmed to 20 grains of hardness. I read the backwash line to the washing machine drain and ran tube approximately 2
Margaret M.
Service for maintenance check up. Arrived to home to go over scope of inspection. Explained to customer how it’s a very through evaluation of all plumbing in home. Started by going into basement where I found the main water valve. Found ball valve to function properly and in good condition if customer had water emergency in home. I then found masters city water softener that was set to proper time and date and had proper salt level in brine tank. Sent unit through few cycles to make sure valve and motor were working properly. I then walked over to natural gas hot water heater. Found the unit to be installed in 1/31/20. Found unit to be a bradford white 75 gallon tank with a spill Switch and st12 potable expansion tank. Found all in proper working condition. After looking at drainage and septic pump customer has I went upstairs to kitchen. Found at kitchen sink customer basket strainer finish was warn do to age. Gave customer estimate for new basket strainers. After looking over all o
Noah D.
Installed pure air electronic air filter. Tested system operation after install.
Margaret M.
Install amana air handler and condenser new line set with thermostat wire program and wire thermostat pressure test and vacuum system new 33 by 30 stamp grill was installed did a start up and explained to customer what was done and how it works their is a balance of $4392.50
Margaret M.
Return trip for large plumbing installation: arrived to home to cut out well tank and softener in main house and also in 2 house on property. Removed old garbage and created bypass for well tank and also softener in second house. Cut out old stand pipe for softener in second house and capped line so that trap would not dry out and create sewage smell. Replaced boiler expansion tank and cleaned up debris. Went back to main house and cut out all bypasses and removed old wiring for old well controls. Filled impressions asp2 with crystal right 200 media. Unit took two and a half cubes of media. Brought softener inside and installed brine tank and backwash line. Brought in stainless steel manifold and asp1 constant pressure control mounted system on wall and piped and wired system in. Mounted the viqua ultraviolet lamp combo and finished the connection to both homes. Ran and purged out air. Calibrated softener and constant pressure system. All working properly at this time. Customer is sati
Chris H.
Customer had heard a loud noise at second floor condenser last night and shut system off, had customer turn system on and I heard bearing in fan motor had gone bad, replaced fan motor with universal fan motor and tested system, also checked standing pressures which were normal, and zip tied all wires inside voltage box of unit.
Scott Y.
Ac tune up. Performed cleaning on ductless units and 2 forced air ac systems. For ductless Cleaned filters and evaporator coils, took temperatures and pressures, systems are new and running normally. 2 central air systems, cleared traps and drains, tested condensate pumps, inspected evaporator coils which were clean. Took delta t readings both units at 20 degrees difference. Pressures for both units are good, both systems 3 years old and running normally. Customer orders and replaces Merv filters himself, both clean.
Chris H.
Completed annual maintenance on air conditioning system from new install last year.
Scott Y.
Ac tune up new install. Replaced filter, cleared trap and drain line, drain line is draining outside normally. Took temperatures, inspected evaporator coil, tested indoor blower. Took outdoor pressures, tested all components. Condenser was layered in pollen and debris, cleaned off coil with hose. System is running normally.
Margaret M.
Wrap the supply duct in the wall with r8 wrap. 12’ duct from the floor to the ceiling it is 14 inches wide. The customer will be opening up the wall himself. We will need to schedule the job when the customer opens the wall up. 7/29/21 Wrapped and tapped 14 inch duct with R8 duct insulation. Wrapped duct as tight as possible. System operational.
Margaret M.
Performed annual AC tuneup. Hosed off outdoor coil. Tested unit. System operational nn
Margaret M.
Upon arrival first thing I noticed was Gloria was very caked with dust and debris. Checked pressures, Pressures were at a 128PSI on the low side. Removed and clean blower wheel as well as entire unit. Unit had 21° split at supply and return. Tested unit, system operational.
Margaret M.
No thermostat REFLECTS NO FINANCE PRICING, $470 TECH CHARGE CREDIT NO T-STAT -$25 7/28/21 Installed 4 ton 16 seer Amana ac condenser with matching 4 ton evaporator coil. Re-commented to existing furnace and ductwork. Flushed lineset. New condensate trap, piping as needed. Started and tested.
Danny B.
Ac Tune Up x2
